|
|
|
Easy Fit Balustrade System
The Easy Fit Balustrade System makes installing Stainless Steel Balustrade easy.
The system is "Swageless", requiring no specialist tools to install such as a swaging tool.
Jaws grip the wire and are locked down with the terminal head and jaw housing.
The Easy Fit Balustrade System is made from 316 Marine Grade Stainless Steel, and provides a modern and clean looking finish to your balustrade.
All products are available to suit either 3.2mm* or 4mm wire.
*3.2mm Terminals are intended for use with 3.2mm 1 x 19 strand braided wire only. We recemmend Easy Fit Balustrade 3.2mm 1x19 braided wire - BSS5103. |
Click Below to view entire range.
 |
|
|
Selection Guide |
Threaded Terminal
Fixes stainless steel wire to metal or timber posts.
Threaded section fits through the post and is secured by a Dome Nut.
 Threaded Terminal 85x3mm Instructions
 Threaded Terminal 85x4mm Instructions |
 |
Threaded Fork
For fixing to metal or timber posts.
Threaded section of the Fork fits through the post and is secured by a Dome Nut.
Ideal for straight sections, or where an angle is required such as fitting wire balustrade to stairs. |
 |
Lag Screw Terminal
Fixes stainless steel wire to timber posts.
Anchors directly into the timber.
Lag Screw Terminal Instructions |
 |
Screw Eye
For fixing to timber posts.
Provides a fixing point for a Forked Terminal to connect into.
Ideal for straight sections, or where an angle is required such as fitting wire balustrade to stairs. |
 |
Fork Terminal
Attaches stainless steel wire to fixed anchor points such as an Eye Saddle, Saddle Plate, Eye Bolt or Screw Eye.
Ideal for straight sections, or where an angle is required such as fitting wire balustrade to stairs.
Fork Terminal Instructions |
 |
Wire Teensioning Kit
The kit contains:
A Swageless Terminal Fitting - attaches Stainless Steel Wire to tensioner.
A Tensioner (Turnbuckle) - to adjust the tension on the wire.
A Threaded Fork - to connect to a suitable mounting such as an Eye Saddle, Saddle Plate, Eye Bolt or Screw Eye.
Wire Tensioning Kit Instructions |
 |
Eye Terminal
Attaches stainless steel wire to a Threaded Fork.
Ideal for straight sections, or where an angle is required such as fitting wire balustrade to stairs.
Eye Terminal Instructions
|
 |
Cylindrical Tensioner
Passes through a timber or metal post, and a Threaded Terminal is fixed into it.
Provides an alternate way of tensioning the wire.
Provides a neat finish on end of post.
Cylindrical Tensioner Instructions
|
 |
|
|
How to use |
It's as easy as...
1. Slide Jaw Housing, Jaws and Pressure Ring onto Stainless Steel Wire
2. Slide Jaw Housing over Jaws
3. Screw Head into Jaw Housing and tighten with a spanner
4. Attach Head to Mounting Point
NOTE
Sealing the unit with a non acidic one-component polyurethane (e.g. Sikaflex® 221) is advised. Disassemble the terminal and fill the jaw housing and cavity
with sealing compound, then assemble the terminal. Repeat this until the sealing compound emerges from the hole through which
the stainless steel wire is inserted. Clean the terminal. After the first dynamic load the terminal must be tightened again.
CAUTION
Jaws should not be re-used. Ensure the dimensions of the terminal and stainless steel wire match.
MAINTENANCE
Check the terminal regularly for damage. Exposure to concentrated salt water or polluted surroundings, can effect the seal. If it is broken
remove the sealing compound. Then rinse the terminal with fresh water and treat with WD40. Re-seal the terminal with non-acidic
one-component polyurethane.
|
|
|